["Michael Lynch" <michaellynch511@xxxxxxxxx>]

God I hope IPv6 is simpler!!

Thanks so much Martin, some great reading there.

Laura mentions that her Wireshark did pick up these LSO packets in the 
trace, so I guess I was just unlucky.
As Graham suggested, I will give a try the "Edit | Preferences | Expand 
Protocols and find IP | Check "Support packet-capture from IP TSO-enabled 
hardware".
I'll let you know if that options resolves the incomplete capture trace.

It really bugs me, these fancy round-about attempts at improving performance 
when they just end up complicating things.
I would suggest to the IEEEE that switches and nics simply support 32K 
packets, and PMTU discovery would automatically ajust for individual neworks 
as required. Problem solved :)



Cheers
Michael.

----- Original Message ----- 
From: "Martin Visser" <martinvisser99@xxxxxxxxx>
To: "Community support list for Wireshark" <wireshark-users@xxxxxxxxxxxxx>
Sent: Friday, January 07, 2011 10:49 PM
Subject: Re: [Wireshark-users] Packets not captured, tcp acking lost 
segments. Large packets


> Michael,
>
> Just done a bit more googling and reading. Certainly this Microsoft
> customer service engineer thinks that a lot of problems are caused by
> Large Segment Offload  -
> http://blogs.msdn.com/b/psssql/archive/2010/02/21/tcp-offloading-again.aspx
>
> There may be some value in turning this off, assuming it is on (at
> least for a test) and seeing whether Wireshark starts behaving and
> your application as well.
>
> Regards, Martin
>
> MartinVisser99@xxxxxxxxx
>
>
>
> On 7 January 2011 22:17, Martin Visser <martinvisser99@xxxxxxxxx> wrote:
> > Michael,
> >
> > "Large packets" are perfectly legal. It is possible that you are
> > sending "jumbo" packets which are supported on gigabit ethernet.
> > Normally you would need to configure that on your servers explicitly
> > though and you need to make sure your clients are also similarly
> > configured to support these. (The reason I didn't mention it earlier
> > is that it I expect you would have mentioned jumbo packets if you were
> > using thhese) It would be good for you to confirm that your server is
> > using Large Segment Offload. This will in the NIC driver
> > configuration.
> > BTW Laura Chappell blogged about LSO at
> > http://laurachappell.blogspot.com/2010/09/analyzing-huge-packets-tsolro.html
> > and in fact I got a bit confused by it about a year or so ago.
> >
> > Yep, that wiki entry is a bit brief, and could be enhanced. The issue
> > I guess is for to understand whether you found a bug or whether you
> > aren't using Wireshark correctly of not. (Having a driver using LSO
> > shouldn't be causing you to drop packets, I am not sure what is going
> > on there). I have just found though a post and response from April
> > 2010 that might shed some light. Have a look at
> > http://www.wireshark.org/lists/wireshark-users/201004/msg00067.html
> > and possibly try out Graham's suggestion at the bottom of
> > http://www.wireshark.org/lists/wireshark-users/201004/msg00068.html
> >
> > One other reason you are getting that could be you are using a teaming
> > adapter. If you are only using Wireshark to monitor a single physical
> > NIC you might not be seeing all the traffic.
> >
> > Regards, Martin
> >
> > MartinVisser99@xxxxxxxxx
> >
> >
> >
> > On 7 January 2011 20:25, Michael Lynch <michaellynch511@xxxxxxxxx> wrote:
> > > Thanks Martin
> > >
> > > I realise that sniffing traffic on the wire is more practical, but I am 
> > > in a
> > > test environment in this case.
> > >
> > > Wouldn't the machine on the mirrored port simply experience the same
> > > problem?
> > > (Oh wait, I see what you mean.. I am monitoring on the server... and the
> > > large packets are out-going, and so therefore if I was sniffing on the 
> > > wire
> > > they would be of normal size.)
> > >
> > > However, I understand this is an open source project, and I really want 
> > > to
> > > help (I beleive many other users have experienced this problem with 
> > > perhaps
> > > no resolution as to what is really going on).
> > > But I'm not about to delve in the ins and outs or even the code of 
> > > WinPCap.
> > >
> > > For a novice user it would be helpful if either a) Large packets at 
> > > least
> > > had a mention, or b) The issue was at least mentioned in
> > > http://wiki.wireshark.org/TCP_ACKed_lost_segment
> > >
> > > Thanks for explaining Martin.
> > > I will post some net caps perhaps on monday back in the office.
> > > I opened the NetMon capture file in Wireshark and the large packets are
> > > listed and the "acked lost segments" are no longer there.
> > > However I still saw some "acked lost segment", god knows where they are
> > > comming from. (I think we have a few problems with this applications use 
> > > of
> > > SOAP, which is what led me here in the first place!!)
> > >
> > > Cheers!
> > > Michael.
> > >
> > > ----- Original Message ----- From: "Martin Visser"
> > > <martinvisser99@xxxxxxxxx>
> > > To: "Community support list for Wireshark" 
> > > <wireshark-users@xxxxxxxxxxxxx>
> > > Sent: Friday, January 07, 2011 3:14 PM
> > > Subject: Re: [Wireshark-users] Packets not captured, tcp acking lost
> > > segments. Large packets
> > >
> > >
> > > > Michael,
> > > >
> > > > Normally your server will be connected to a switch. If this is a
> > > > manageable switch, you should be able to configure it to port-mirror,
> > > > which means a copy of the traffic on one port is sent to another port.
> > > > This will enable easy monitoring of your traffic, and you will see
> > > > what is actually going on the wire. When I meant "avoid", it is more
> > > > about making sure you see what is on the wire rather than the tricks
> > > > that the driver might be doing. (I try to avoid installing Wireshark
> > > > or Net Mon on production servers - not that it doesn't work, but I
> > > > don't want my measuring application potentially affecting the normal
> > > > performance of the server).
> > > >
> > > > I'm not sure if there is possibly an issue with WinPcap library not
> > > > working properly on your box of not. You might want to post a small
> > > > capture file showing what you saw with Wireshark and what you captured
> > > > with Net Mon. (Also note that Wireshark can read Net Mon files - does
> > > > this show the difference as well?)
> > > >
> > > > Regards, Martin
> > > >
> > > > MartinVisser99@xxxxxxxxx
> > > >
> > > >
> > > >
> > > > On 7 January 2011 14:27, Michael Lynch <michaellynch511@xxxxxxxxx> 
> > > > wrote:
> > > > > Thanks Martin
> > > > >
> > > > > I read up on LSO. It explains how these >4K packets are appearing
> > > > >
> > > > > Yes I am running Wireshark on the application server. I had a hard 
> > > > > time
> > > > > installing it on my switch!! No CD-rom drive!! :)
> > > > > (I am not sure what you mean by 'Server Switch')
> > > > >
> > > > > But why is MS Net Mon seeing these large packets?
> > > > >
> > > > > Wireshark is providing misleading information and I don't think i'm 
> > > > > the
> > > > > only
> > > > > one that is suffering major confusion.
> > > > > I think my self lucky as I have witnessed the packets in NetMon.
> > > > > Most users on the net seem to have presumed that packets are being 
> > > > > lost!
> > > > >
> > > > > > Wireshark will see the large segments go out.
> > > > >
> > > > > But its not...?
> > > > >
> > > > > > You might want to capture on your server switch rather than the 
> > > > > > server
> > > > > > to avoid seeing this.
> > > > >
> > > > > I don't want to avoid packets, I want to see the packets!
> > > > >
> > > > >
> > > > >
> > > > > Cheers
> > > > > Michael.
> > > > >
> > > > >
> > > > >
> > > > > ----- Original Message ----- From: "Martin Visser"
> > > > > <martinvisser99@xxxxxxxxx>
> > > > > To: "Community support list for Wireshark"
> > > > > <wireshark-users@xxxxxxxxxxxxx>
> > > > > Sent: Friday, January 07, 2011 1:46 PM
> > > > > Subject: Re: [Wireshark-users] Packets not captured, tcp acking lost
> > > > > segments. Large packets
> > > > >
> > > > >
> > > > > > It sounds like you are capturing traffic on the server rather than 
> > > > > > the
> > > > > > wire. If your server NIC and driver does Large Segment Offload, the
> > > > > > segmentation is done by the NIC, which allows the transfer from your
> > > > > > kernel to the NIC do be done in larger chunks, meaning a more
> > > > > > efficient transfer. Wireshark will see the large segments go out.
> > > > > >
> > > > > > You might want to capture on your server switch rather than the 
> > > > > > server
> > > > > > to avoid seeing this.
> > > > > >
> > > > > > Regards, Martin
> > > > > >
> > > > > > MartinVisser99@xxxxxxxxx
> > > > > >
> > > > > >
> > > > > >
> > > > > > On 7 January 2011 11:25, Michael Lynch <michaellynch511@xxxxxxxxx>
> > > > > > wrote:
> > > > > > > Hi All
> > > > > > >
> > > > > > > I think I've found something everyone may be interested in...
> > > > > > >
> > > > > > > In wireshark I am monitoring traffic of a SOAP application.
> > > > > > >
> > > > > > > Upon transfer of a BLOB, wire shark is showing many "Tcp ACKed lost
> > > > > > > segment"
> > > > > > > packets.
> > > > > > > On top of this there is no evidence of any of the SOAP data, other 
> > > > > > > than
> > > > > > > the
> > > > > > > initial header.
> > > > > > >
> > > > > > > Now I've search for this lost segment business, and no forums really
> > > > > > > seem
> > > > > > > to
> > > > > > > have much of a solution other than perhaps disabling sequence 
> > > > > > > analysis.
> > > > > > >
> > > > > > > However I think I have found the problem, but I have no 
> > > > > > > understanding
> > > > > > > of
> > > > > > > the
> > > > > > > whats and whys.
> > > > > > >
> > > > > > > In Microsoft Net Mon, the data packets ARE THERE!!!
> > > > > > >
> > > > > > > i.e
> > > > > > > Sent packet: Captured Frame Length = 4434, Media Type = Ethernet...
> > > > > > > Continuaion to packet #76.
> > > > > > > Received packet: Ack
> > > > > > >
> > > > > > > The received packet is the only packet that shows up in Wireshark! 
> > > > > > > (I
> > > > > > > have
> > > > > > > cross referenced the Packet ID)
> > > > > > > Wireshark is NOT COLLECTING LARGE PACKETS!!
> > > > > > >
> > > > > > > I have no idea how packets THAT LARGE got onto the wire IN THE FIRST
> > > > > > > PLACE!!
> > > > > > >
> > > > > > > What is going on??!! :)
> > > > > > >
> > > > > > > Cheers
> > > > > > > Michael
> > > > > > >
> > > > > > >
> > > > > > > ___________________________________________________________________________
> > > > > > > Sent via: Wireshark-users mailing list 
> > > > > > > <wireshark-users@xxxxxxxxxxxxx>
> > > > > > > Archives: http://www.wireshark.org/lists/wireshark-users
> > > > > > > Unsubscribe: https://wireshark.org/mailman/options/wireshark-users
> > > > > > > mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > > >
> > > > > >
> > > > > > ___________________________________________________________________________
> > > > > > Sent via: Wireshark-users mailing list 
> > > > > > <wireshark-users@xxxxxxxxxxxxx>
> > > > > > Archives: http://www.wireshark.org/lists/wireshark-users
> > > > > > Unsubscribe: https://wireshark.org/mailman/options/wireshark-users
> > > > > >
> > > > > > mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > > >
> > > > >
> > > > > ___________________________________________________________________________
> > > > > Sent via: Wireshark-users mailing list <wireshark-users@xxxxxxxxxxxxx>
> > > > > Archives: http://www.wireshark.org/lists/wireshark-users
> > > > > Unsubscribe: https://wireshark.org/mailman/options/wireshark-users
> > > > > mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe
> > > >
> > > > ___________________________________________________________________________
> > > > Sent via: Wireshark-users mailing list <wireshark-users@xxxxxxxxxxxxx>
> > > > Archives: http://www.wireshark.org/lists/wireshark-users
> > > > Unsubscribe: https://wireshark.org/mailman/options/wireshark-users
> > > >
> > > > mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe
> > >
> > > ___________________________________________________________________________
> > > Sent via: Wireshark-users mailing list <wireshark-users@xxxxxxxxxxxxx>
> > > Archives: http://www.wireshark.org/lists/wireshark-users
> > > Unsubscribe: https://wireshark.org/mailman/options/wireshark-users
> > > mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe
> ___________________________________________________________________________
> Sent via:    Wireshark-users mailing list <wireshark-users@xxxxxxxxxxxxx>
> Archives:    http://www.wireshark.org/lists/wireshark-users
> Unsubscribe: https://wireshark.org/mailman/options/wireshark-users
>
> mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe