["marco\@marcomp\.it" <marco@xxxxxxxxxx>]

Hi Lars,

     if I do not add any filter I can capture all the traffic ( that do not match as source / destination or both ) the mirroring port send me. While if I enable a filter ( like "igmp" for example )I can only see the traffic that can be accepted by the subnet I configure on my eth interface .....

 

Regards,
Marco

 

 

Da: wireshark-users-bounces@xxxxxxxxxxxxx

A: "Community support list for Wireshark" wireshark-users@xxxxxxxxxxxxx

Cc:

Data: Thu, 29 Apr 2010 15:03:20 +0200

Oggetto: Re: [Wireshark-users] pcap / winpcap filters

> Hi,

> That's not a problem. In **promsicous mode** (checked?), you will see any traffic coming out of the mirror port, regardless if it's on your local subnet or not.

> Have you tried sniffing without any filter? Do you see the traffic of the other subnet then?

> I suspect your problem is more related to your port mirroring setup than to Wireshark filters.

>

> Regards,

> Lars Ruoff

>

>

> ________________________________________

> From: wireshark-users-bounces@xxxxxxxxxxxxx [mailto:wireshark-users-bounces@xxxxxxxxxxxxx] On Behalf Of marco@xxxxxxxxxx

> Sent: jeudi 29 avril 2010 14:49

> To: wireshark-users@xxxxxxxxxxxxx

> Subject: Re: [Wireshark-users] pcap / winpcap filters

>

> Hi,

>     yes, that's what I did in the past but if I use this filter string I can only get the packet that lookup on my ethernet interface ....  while I need to see all the packets that are not send to / comes from my eth interface subnet .

>  

> I did a port mirroring on a Layer3 switch so on the mirroring  port I can see all the packets of some subnet and they will necessary not match my eth interface subnet .....

>

>

> Thanks !

> Marco

>

> Da: wireshark-users-bounces@xxxxxxxxxxxxx

> A: "Community support list for Wireshark" wireshark-users@xxxxxxxxxxxxx

> Cc:

> Data: Thu, 29 Apr 2010 14:09:46 +0200

> Oggetto: Re: [Wireshark-users] pcap / winpcap filters

>

> > Hi,

> >

> > Would that be a capture filter like: 'port 53 or port 5060'

> >

> > Thanks,

> > Jaap

> >

> > On Thu, 29 Apr 2010 11:39:17 +0200, "marco\@marcomp\.it"

> > wrote:

> > > I need to filter some traffic (before capturing it) using the pcap /

> > > winpcap filter but this traffic comes from some different subnet (

> > > different from my eth interface subnet ).

> > > So if I apply a filter the pcap show me the packet that can lookup on my

> > > eth interface only ...

> > > How can I get the filtered traffic that comes from "everywhere"

> > > (0.0.0.0/0) ?

> > >

> > > I need to filter the data traffic before sending it to whireshark

> > because

> > > I only need to check the DNS and SIP traffic for a long time ( may be

> > for

> > > more than 1 week )... so I don't want to store Gbyte and Gbyte of not

> > > helpful data on my pc.....

> > >

> > > Have you any suggestion ?

> > >

> > >

> > > Marco

> > >

> > subscribe

> > ___________________________________________________________________________

> > Sent via: Wireshark-users mailing list

> > Archives: http://www.wireshark.org/lists/wireshark-users

> > Unsubscribe: https://wireshark.org/mailman/options/wireshark-users

> > mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe

> ___________________________________________________________________________

> Sent via: Wireshark-users mailing list

> Archives: http://www.wireshark.org/lists/wireshark-users

> Unsubscribe: https://wireshark.org/mailman/options/wireshark-users

> mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe