[Gerald Combs <gerald@xxxxxxxxxxxxx>]

FWIW, Sean Walberg gave an excellent VoIP troubleshooting presentation
yesterday at Sharkfest:

http://www.cacetech.com/sharkfest.09/AU9-Walberg-Expose%20VoIP%20problems%20with%20wireshark.ppt

Jeffrey Walton wrote:
> Hi Mark,
> 
> I jumping in with Ryan because I agree with his experience. Here's
> some of mine (for what it is worth)...
> 
>>> The phone system is manufactured by Allworx
> No experience. Perhaps someone else can comment on Allworx
> 
>>> The switches we are using are Dell 3548P PowerConnects.
>>> I've configure the network to use two VLANs - one for phone,
>>> one for everything else - and used VLAN tagging and CoS to
>>> prioritize VoIP traffic. I've actually combed through the configs
>>> with a Dell engineer, and we're good there.
> I've had a number of hard to track down issues related to Dell
> hardware and the Broadcom ethernet gear. During the two nastier
> issues, the port would process data fine for a while. Then throughput
> would drop to its knees. It was as if packets were being dropped
> following a reciprocal-exponential curve. The Dell hardware never
> reported any problems.
> 
> Also, is the problem with all phones with a more or less random
> distribution? Does it look random but with a single switch in common?
> or is it related to a collection of handsets?
> 
> Jeff
> 
> On 6/19/09, Ryan Zuidema <ryan.zuidema@xxxxxxxxxxx> wrote:
>> Running computers through the phones is entirely normal, the point of VoIP
>> is to have a 1 wire office. That said most VoIP installs I have seen still
>> run separate lines. The reasoning is that it’s easier to maintain and the
>> cost difference is small to run two wires as opposed to one.
>>
>> It’s not surprising that the server doesn’t tag. It’s reasonable to assume
>> that ALL traffic to that port would be on the phone VLAN and high priority.
>> The only reason your endpoints need to tag is if they have multiple QoS
>> requirements.
>>
>> Ryan
>>
>> From: wireshark-users-bounces@xxxxxxxxxxxxx
>> [mailto:wireshark-users-bounces@xxxxxxxxxxxxx] On Behalf Of
>> Mark Jeffers
>>  Sent: Friday, June 19, 2009 6:40 AM
>>  To: Community support list for Wireshark
>>  Subject: Re: [Wireshark-users] Huge VoIP Problem :(
>>
>> The phones actually act as a level 2 switch themselves.   They tag their own
>> packets for VLAN9 (the voice VLAN on my network) and tag the packets of the
>> PC attached to them (if there is one) as VLAN1.
>>
>> Attaching a phone and a pc to the same switch port has made me nervous from
>> day one, but the vendor swore up and down it would work no problem.
>>
>> Also, one thing that has me shaking my head in disbelief is that while
>> Allworx built their phones with VLAN tagging abilities, their main phone
>> server can't tag its own packets.
>>
>> But anyway, I was of course suspicious of the pc/phone combo, but some of my
>> most problematic phones have no pc attached to them.  Plus, I figured
>> building the VLANs would solve any problem related to that.   Perhaps I was
>> wrong?
>>
>> Cheers,
>>
>> mj
>>
>> [SNIP]
>>
>> From: wireshark-users-bounces@xxxxxxxxxxxxx
>> [mailto:wireshark-users-bounces@xxxxxxxxxxxxx] On Behalf Of
>> Mark Jeffers
>>  Sent: Wednesday, June 17, 2009 9:32 AM
>>  To: wireshark-users@xxxxxxxxxxxxx
>>  Subject: [Wireshark-users] Huge VoIP Problem :(
>>
>> We've been having a terrible time with a new VoIP system on our network.
>>
>> The phone system is manufactured by Allworx - it is tied to the outside
>> world with a standard PRI, so the only IP portion of calls takes place
>> between our LAN phone server and the IP extensions.
>>
>> Several of the extensions are having packet loss problems resulting in
>> echoes, "static", dropped audio, etc.  The problems are intermittent and
>> jump around to different phones on the network.
>>
>> The switches we are using are Dell 3548P PowerConnects.   I've configure the
>> network to use two VLANs - one for phone, one for everything else - and used
>> VLAN tagging and CoS to prioritize VoIP traffic.   I've actually combed
>> through the configs with a Dell engineer, and we're good there.
>>
>> So I'm relatively new to both VoIP and hardcore packet analysis, but I found
>> an excellent article on troubleshooting VoIP using wireshark and followed
>> instructions.
>>
>> I mirrored one of the Trunk ports on the switch to my laptop, configured
>> Wireshark to filter out all but UDP packets and let it run for about an
>> hour.
>>
>> The results are horrible... I've attached screenshot images so you guys
>> might be able to help me figure this out.
>>
>> When I ran an RTP Stream analysis, there were blocks of sessions where
>> several of them had "Max Delta" in the thousands (some in the 9000s),
>> resulting in 90+% packet loss!  See Image1,jpg
>>
>> I drilled down into one of the streams to see a bunch of "Wrong Sequence nr"
>> messages - See Image2.jpg
>>
>> I went to VoIP Calls under the statistics menu, and pulled up the same call
>> shown in Image2 - looked fine to me, but I'm a noob - See Image3.jpg
>>
>> I'm at a loss here.   Obviously severe network issues, or the Phone Switch
>> is bad.   I've tried everything I can think of to no avail.  Anybody have
>> any ideas of what might be wrong, or what further information I should
>> gather to help pinpoint the issue?   I'm going nuts here and any help would
>> be greatly, greatly appreciated.  :)
>>
>> Cheers,
>>
>> Mark
>> [SNIP]
> ___________________________________________________________________________
> Sent via:    Wireshark-users mailing list <wireshark-users@xxxxxxxxxxxxx>
> Archives:    http://www.wireshark.org/lists/wireshark-users
> Unsubscribe: https://wireshark.org/mailman/options/wireshark-users
>              mailto:wireshark-users-request@xxxxxxxxxxxxx?subject=unsubscribe