[Adriana Matei <adriana.matei@xxxxxxxxxxxxxx>]

   Yes, I did that, but still I get a warning like :

        Stack file used: c:/program 
files/tektronix/k15/stacks/wimax_r1/wimax_r1_r1_802.16e_wimax_rel_evolium_2_31.stk
         Warning: stk file not matched in the 'K12 Protocols' table

   Where is Wireshark exactly looking when it is saying "Stack file 
used:" because I don't have a "c:/program 
files/tektronix/k15/stacks/wimax_r1/wimax_r1_r1_802.16e_wimax_rel_evolium_2_31.stk" 
That is not the path to the stack file that I want to use.
   Can I somehow redirect the path that it is using for the stack file 
in order to use a specific stack file that I have in a different place 
from where Wireshark is installed?

Luis EG Ontanon wrote:
> The K12 configuration file applies to versions up to 0.99.5, 1.0 its
> far newer it instead uses a table.
>
> The k12 "dissector" now uses a simple table that contains two parts:
> match and proto:
>
> - "match" should contain a string that is an univocously identifiable
> part of either the port name or a stack filename (.stk).
>
> - "proto" contains the lowest layer protocol to be used (i.e. the
> encapsulation mtp2, eth, sscf-nni, ...).
>
>
> Once you populate your table with the various entries Wireshark will
> look for "match" in either the port name or the stack filename for
> that port and if there is a match for a given packet it will attempt
> to decode its contents using "proto".
>
>
> On Fri, Jul 18, 2008 at 1:19 PM, Adriana Matei
> <adriana.matei@xxxxxxxxxxxxxx> wrote:
>   
> >  Hello all,
> >
> >  How should I configure my Wireshark( version 1.0.1) in order to read
> > this type of files? I read about *Tektronix K12xx/K15 .rf5 files* on
> > http://wiki.wireshark.org/K12 but I got lost at this part:
> >
> > "The configuration file contains a list of
> > stk-file/encapsulation-protocol pairings separated by a space.
> >
> > To set wireshark to use a k12 config file go to
> > Preferences->Protocols->k12 and write the filename in the "Configuration
> > filename" preference. You can specify a k12 config file using  -o
> > 'k12.config: /path/to/k12_config  on the command line.
> >
> > Example configuration file
> >
> > # comments are lines that start with a '#'
> > # sorry no spaces in filenames are allowed yet
> > C:\K1297\stacks\umts_iu\umts_iu_ranap_alcap_2002-03.stk sscf-nni
> > C:\K1297\stacks\umts_iu\umts_iu_ranap_alcap_2002-09.stk sscop
> > D:\K15\stacks\gprs\gprs_Gb_R99.stk fr
> > D:\K15\stacks\umts_iu\umts_iu_ranap_alcap_2002-09.stk sscop
> > D:\K15\stacks\umts_iu\umts_iu_ranap_alcap.stk sscop
> > C:\K1205\stacks\whibisup.stk mtp
> > C:\K1297\stacks\gsm2p\gsm2p_gmsc.stk mtp2
> > C:\K1297\stacks\umts_iu\umts_iu_ranap_alcap.stk sscop " ...
> >
> >  Because in Preferences->Protocols->k12 i don't have a option called "Configuration filename" and I don't know where to make the configuration from the example from above.
> >  Also I tried to open wireshark from cmd (I work on Windows) with the -o 'k12.config: /path/to/k12_config option but I get a invalid -o flag k12.config
> >  I mention that in Preferences->Protocols-> I have k12xx and not k12.
> > Can anyone help me?
> >
> > Thanks in advance
> >
> >
> > _______________________________________________
> > Wireshark-users mailing list
> > Wireshark-users@xxxxxxxxxxxxx
> > https://wireshark.org/mailman/listinfo/wireshark-users
> >
> >     
>
>
>
>