["Anders Broman" <a.broman@xxxxxxxxx>]

Hi,
I have checked in a change to make it possible to "decode as"
For the SCTP port used for NBAP. I also updated the value string for the
Registered PPID's.
Committed revision 21927.
You can download it from the automated builds section in a few hours.
Regards
Anders

-----Ursprungligt meddelande-----
Från: wireshark-users-bounces@xxxxxxxxxxxxx
[mailto:wireshark-users-bounces@xxxxxxxxxxxxx] För Michael Tuexen
Skickat: den 24 maj 2007 22:26
Till: Community support list for Wireshark
Ämne: Re: [Wireshark-users] NBAP over SCTP

Hi Martin,

The trace shows that you use payload protocol identifier 17
for NBAP, which is already taken.

 From http://www.iana.org/assignments/sctp-parameters

SCTP Payload Protocol Identifiers                         REFERENCE
---------------------------------                         ---------

   1 - IUA                                                 [RFC4233]
   2 - M2UA                                                [RFC3331]
   3 - M3UA                                                [RFC4666]
   4 - SUA                                                 [RFC2960]
   5 - M2PA                                                [RFC2960]
   6 - V5UA                                                [RFC2960]
   7 - H.248                                                 [H.248]
   8 - BICC/Q.2150.3	                            [Q.1902.1/Q.2150.3]
   9 - TALI                                                [RFC3094]
10 - DUA                                                 [RFC4129]
11 - ASAP       <draft-ietf-rserpool-asap-03.txt>            [Ong]
12 - ENRP       <draft-ietf-rserpool-enrp-03.txt>            [Ong]
13 - H.323                                                 [H.323]
14 - Q.IPC/Q.2150.3                            [Q.2631.1/Q.2150.3]
15 - SIMCO      <draft-kiesel-midcom-simco-sctp-00.txt>   [Kiesel]
16 - DDP Segment Chunk                 [RFC-ietf-rddp-sctp-07.txt]
17 - DDP Stream Session Control        [RFC-ietf-rddp-sctp-07.txt]

Is there a specification for NBAP over SCTP? The best way is to
register with IANA a payload protocol identifier and possibly also
an SCTP port number.

Best regards
Michael

On May 24, 2007, at 10:03 PM, Martin Andersson wrote:

> Hope this help.
>
> rg/Martin
>
> Anders Broman wrote:
>> Hi,
>> If you could share a trace file we could look into how that can be  
>> done.
>> Regards
>> Anders
>>
>> -----Ursprungligt meddelande-----
>> Från: wireshark-users-bounces@xxxxxxxxxxxxx
>> [mailto:wireshark-users-bounces@xxxxxxxxxxxxx] För Martin Andersson
>> Skickat: den 24 maj 2007 21:46
>> Till: wireshark-users@xxxxxxxxxxxxx
>> Ämne: [Wireshark-users] NBAP over SCTP
>>
>> How is't possible to get NBAP dissected over SCTP.
>> Today it "stops" at SCTP level and only show binary data (which is  
>> actual NBAP data).
>> Preferably both in wireshark and tshar.
>>
>> cheers.
>> _______________________________________________
>> Wireshark-users mailing list
>> Wireshark-users@xxxxxxxxxxxxx
>> http://www.wireshark.org/mailman/listinfo/wireshark-users
>>
>> _______________________________________________
>> Wireshark-users mailing list
>> Wireshark-users@xxxxxxxxxxxxx
>> http://www.wireshark.org/mailman/listinfo/wireshark-users
>>
>
> <nbap_over_sctp.cap.gz>
> _______________________________________________
> Wireshark-users mailing list
> Wireshark-users@xxxxxxxxxxxxx
> http://www.wireshark.org/mailman/listinfo/wireshark-users

_______________________________________________
Wireshark-users mailing list
Wireshark-users@xxxxxxxxxxxxx
http://www.wireshark.org/mailman/listinfo/wireshark-users