["Anders Broman" <a.broman@xxxxxxxxx>]

Hi,
Changing the chargecontrol.xml file to:
		<avp name="Volume-Quota-Threshold" code="869"
mandatory="must" may-encrypt="no" protected="may">
			<type type-name="Unsigned32"/>
		</avp>
Works for me.
 Quota-Holding-Time is defined in the dictionary.xml file and in the
chargecontrol.xml(as vendor specific)perhaps Volume-Quota-Threshold
Should be in both files as well. I think there is a bit of a mess with the
older 3GPP specs misusing
The common AVP's which has been corrected in later specs.
Best regards
Anders

________________________________________
Från: wireshark-users-bounces@xxxxxxxxxxxxx
[mailto:wireshark-users-bounces@xxxxxxxxxxxxx] För Frederiek Debruyne
Skickat: den 26 februari 2007 14:52
Till: Community support list for Wireshark
Ämne: Re: [Wireshark-users] Diameter unknown AVPs

Hi,

The cleared flag bits seem not to be the real problem that causes Wireshark
not to recognize this Volume-Quota-Threshold AVP. I removed the
‘vendor-id="TGPP"’ part from the related XML file line, and set
vendor-bit="mustnot". That did not help.
Furthermore, the 3GPP AVP Quota-Holding-Time, on the other hand, is
recognized without any problem, while all its flag bits are cleared too.

Regards,

Frederiek

________________________________________
From: wireshark-users-bounces@xxxxxxxxxxxxx
[mailto:wireshark-users-bounces@xxxxxxxxxxxxx] On Behalf Of Anders Broman
(AL/EAB)
Sent: maandag 26 februari 2007 13:27
To: Community support list for Wireshark
Subject: Re: [Wireshark-users] Diameter unknown AVPs

Hi,
The problem is that Wireshark expects this to be a vendor AVP but it's sent
as a "normal" one.
I think this was changed in more recent versions of the 3GPP doc's to be
Vendor specific AVP:s.
 
The simplest soulution for you is to edit the XML file and remove
"Vendor-id="TGPP" " from the
relevant AVP:s
 
Best regards
Anders 

________________________________________
From: wireshark-users-bounces@xxxxxxxxxxxxx
[mailto:wireshark-users-bounces@xxxxxxxxxxxxx] On Behalf Of Frederiek
Debruyne
Sent: den 26 februari 2007 09:10
To: Community support list for Wireshark
Subject: Re: [Wireshark-users] Diameter unknown AVPs
Hi Anders,

Did you receive the sample file? Is the Volume-Quota-Threshold AVP
recognized in your case?

Regards,

Frederiek

________________________________________
From: wireshark-users-bounces@xxxxxxxxxxxxx
[mailto:wireshark-users-bounces@xxxxxxxxxxxxx] On Behalf Of Anders Broman
(AL/EAB)
Sent: vrijdag 23 februari 2007 16:42
To: Community support list for Wireshark
Subject: SV: [Wireshark-users] Diameter unknown AVPs

Hi,
That should suffice, can you send me a small sample file?
Best regards
Anders

________________________________________
Från: wireshark-users-bounces@xxxxxxxxxxxxx genom Frederiek Debruyne
Skickat: fr 2007-02-23 16:27
Till: Community support list for Wireshark
Ämne: Re: [Wireshark-users] Diameter unknown AVPs
Hi,
 
The “Attempt to load/use Diameter XML Dictionary” checkbox, in the
preferences for Diameter, is checked.
The Diameter XML dictionary is set to “C:\Program
Files\Wireshark\diameter/dictionary.xml”.
 
The Volume-Quota-Threshold AVP (code 869) is not recognized. This AVP is not
defined by IETF RFC 3588, but by a 3GPP specification.
 
I am not that familiar with XML, though I noticed the occurrence of
following lines in file chargecontrol.xml:
 
<avp name="Volume-Quota-Threshold" code="869" mandatory="must"
may-encrypt="no" protected="may" vendor-bit="must" vendor-id="TGPP">
<type type-name="Unsigned32"/>
</avp>
 
I’m not sure whether this should be sufficient. It does not seem to be,
since the AVP is still not recognized.
 
Regards,
 
Frederiek
________________________________________
From: wireshark-users-bounces@xxxxxxxxxxxxx
[mailto:wireshark-users-bounces@xxxxxxxxxxxxx] On Behalf Of Anders Broman
(AL/EAB)
Sent: vrijdag 23 februari 2007 16:04
To: Community support list for Wireshark
Subject: SV: [Wireshark-users] Diameter unknown AVPs
 
Hi,
AVP:s can be dissected either by the data in the file packet-diameter-defs.h
or by the Diameter
XML files if those preferences are set. See the wiki page for details.
The XML library is more updated than the file. What AVP:s are not
recognised?
 
Best regards
Anders
 
________________________________________
Från: wireshark-users-bounces@xxxxxxxxxxxxx genom Frederiek Debruyne
Skickat: fr 2007-02-23 15:33
Till: wireshark-users@xxxxxxxxxxxxx
Ämne: [Wireshark-users] Diameter unknown AVPs
Hi,

I frequently use Wireshark to analyze Diameter protocol traffic. I
notice that not all AVPs are recognized. That is, the packet details
frame contains a line with "Unknown AVP" in that case. What must be done
to make Wireshark recognize these AVPs?

I am using the latest Wireshark version, i.e. version 0.99.5.

Regards,

Frederiek


This email has been processed by SmoothZap - www.smoothwall.net

_______________________________________________
Wireshark-users mailing list
Wireshark-users@xxxxxxxxxxxxx
http://www.wireshark.org/mailman/listinfo/wireshark-users


This email has been processed by SmoothZap - www.smoothwall.net


This email has been processed by SmoothZap - www.smoothwall.net


This email has been processed by SmoothZap - www.smoothwall.net