Thanks Anders that works.
For my information I was trying to see if there was a preferred
way of getting dissection information from a 'encapsulating'
layer.
I'm almost done.
The last thing I'm trying to do (I think) is figure out if I
can add IOS5 to the VoIP calls analysis.
--
Michael Lum Principal Software Engineer
4600 Jacombs Road +1.604.276.0055
Richmond, B.C.
Canada V6V 3B1
Star Solutions
-----Original Message-----
From: wireshark-dev-bounces@xxxxxxxxxxxxx [mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Anders Broman
Sent: November 19, 2008 11:40 AM
To: 'Developer support list for Wireshark'
Subject: Re: [Wireshark-dev] How do I get RTP payload type from sub-dissector
Hi,
How about having a handle per type :)
/Anders
-----Ursprungligt meddelande-----
Från: wireshark-dev-bounces@xxxxxxxxxxxxx
[mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] För Michael Lum
Skickat: den 19 november 2008 18:52
Till: Developer support list for Wireshark
Ämne: Re: [Wireshark-dev] How do I get RTP payload type from sub-dissector
Yes, I have the following:
dissector_add_string("rtp_dyn_payload_type", "EVRC", evrc_handle);
dissector_add_string("rtp_dyn_payload_type", "EVRCB", evrc_handle);
dissector_add_string("rtp_dyn_payload_type", "EVRCWB", evrc_handle);
but when a particular packet is being dissected I want to know if it is EVRC or EVRCB or EVRCWB so that I can use different header fields.
--
Michael Lum Principal Software Engineer
4600 Jacombs Road +1.604.276.0055
Richmond, B.C.
Canada V6V 3B1
Star Solutions
-----Original Message-----
From: wireshark-dev-bounces@xxxxxxxxxxxxx
[mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Anders Broman
Sent: November 19, 2008 9:48 AM
To: Developer support list for Wireshark
Subject: Re: [Wireshark-dev] How do I get RTP payload type from sub-dissector
Hi,
Have a look at pcaket-amr or pcaket-h264.c
But basically:
dissector_add_string("rtp_dyn_payload_type","AMR", amr_handle);
You can also do
Regards
Anders
-----Original Message-----
From: wireshark-dev-bounces@xxxxxxxxxxxxx
[mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Michael Lum
Sent: den 19 november 2008 18:39
To: Developer support list for Wireshark
Subject: [Wireshark-dev] How do I get RTP payload type from sub-dissector
Hello,
I have a dissector that gets called after RTP.
How can I get the payload type for the packet from the RTP dissection in my dissector ?
My dissector is called based on dynamic payload types.
Thanks
--
Michael Lum Principal Software Engineer
4600 Jacombs Road +1.604.276.0055
Richmond, B.C.
Canada V6V 3B1
Star Solutions
_______________________________________________
Wireshark-dev mailing list
Wireshark-dev@xxxxxxxxxxxxx
https://wireshark.org/mailman/listinfo/wireshark-dev
_______________________________________________
Wireshark-dev mailing list
Wireshark-dev@xxxxxxxxxxxxx
https://wireshark.org/mailman/listinfo/wireshark-dev
_______________________________________________
Wireshark-dev mailing list
Wireshark-dev@xxxxxxxxxxxxx
https://wireshark.org/mailman/listinfo/wireshark-dev
_______________________________________________
Wireshark-dev mailing list
Wireshark-dev@xxxxxxxxxxxxx
https://wireshark.org/mailman/listinfo/wireshark-dev