Hi,
I had a similar problem and the easiest way was adding a prepared SDP
frame to the beginning of the captured file.
Best regards,
Balint
2008. 11. 17, hétfő keltezéssel 18.52-kor Anders Broman ezt írta:
> Hi,
> I think rtp_add_address() should do it, see packet-uma.c SIP RTCP etc.
> You might have to add debug code to see where it fails...( if(tree)
> causing problems?).
> Regards
> Anders
>
> -----Original Message-----
> From: wireshark-dev-bounces@xxxxxxxxxxxxx
> [mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Michael Lum
> Sent: den 17 november 2008 17:59
> To: Developer support list for Wireshark
> Subject: Re: [Wireshark-dev] How do you get RTP recognized by Wireshark
> ?
>
> Yes, I've tried that, thanks.
>
> Wireshark shows the packets as RTP but does not know the payload type.
>
> I would like to make modifications to the source so that Wireshark will
> understand the CODECs specified in the IOS5 signaling and then
> subsequently call another dissector for RFC3558.
>
> Thanks.
>
>
> --
> Michael Lum Principal Software Engineer
> 4600 Jacombs Road +1.604.276.0055
> Richmond, B.C.
> Canada V6V 3B1
> Star Solutions
> -----Original Message-----
> From: wireshark-dev-bounces@xxxxxxxxxxxxx
> [mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Abhik Sarkar
> Sent: November 15, 2008 1:53 AM
> To: Developer support list for Wireshark
> Subject: Re: [Wireshark-dev] How do you get RTP recognized by Wireshark
> ?
>
> Hi Michael,
>
> I don't know much about RTP, but I think I remember someone answering a
> similar question recently... have you already trying turning on the
> preference for RTP protocol called "Try to decode RTP outside of
> conversations"?.
>
> HTH
> Abhik.
>
> On Fri, Nov 14, 2008 at 10:06 PM, Michael Lum
> <michael.lum@xxxxxxxxxxxxxxxxx> wrote:
> > Hi,
> >
> > I have RTP streams that are set up with an unrecognized signaling
> > protocol. I.e. not SIP/MGCP, etc.
> >
> > Can somebody give me a quick run down on what to change so that the
> > streams can be recognized as RTP ?
> >
> > I thought all I might have to do was add a call to
> > rtp_add_address() with the correct IP address, port, payload, etc.
> > but it doesn't appear to work.
> >
> > Any help would be great.
> >
> > Thanks.
> >
> > --
> > Michael Lum Principal Software Engineer
> > 4600 Jacombs Road +1.604.276.0055
> > Richmond, B.C.
> > Canada V6V 3B1
> > Star Solutions
> > _______________________________________________
> > Wireshark-dev mailing list
> > Wireshark-dev@xxxxxxxxxxxxx
> > https://wireshark.org/mailman/listinfo/wireshark-dev
> >
> _______________________________________________
> Wireshark-dev mailing list
> Wireshark-dev@xxxxxxxxxxxxx
> https://wireshark.org/mailman/listinfo/wireshark-dev
> _______________________________________________
> Wireshark-dev mailing list
> Wireshark-dev@xxxxxxxxxxxxx
> https://wireshark.org/mailman/listinfo/wireshark-dev
> _______________________________________________
> Wireshark-dev mailing list
> Wireshark-dev@xxxxxxxxxxxxx
> https://wireshark.org/mailman/listinfo/wireshark-dev