["Anders Broman \(AL/EAB\)" <anders.broman@xxxxxxxxxxxx>]

Hi,

Sorry my bad, the lines to remove are:

 cd asn1                                                                    -- As this dir does not exist
 $(MAKE) /$(MAKEFLAGS) -f Makefile.nmake clean    -- That would have been run in ../asn1
 cd ..                                                                        -- step up one level from asn1

 

Or use a tarball from http://wireshark.org/download/automated/src/

 

Brg

Anders 

---

From: wireshark-dev-bounces@xxxxxxxxxxxxx [mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Andrew.Martin@xxxxxxxxxxxxxxxxxxxxxx
Sent: den 24 oktober 2006 15:59
To: wireshark-dev@xxxxxxxxxxxxx
Subject: Re: [Wireshark-dev] nmake U1077 errors

Ok so now I have the same error for wiretap, the one right under asn1.

 

Doh!

---

From: wireshark-dev-bounces@xxxxxxxxxxxxx [mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Anders Broman (AL/EAB)
Sent: 24 October 2006 10:47
To: Developer support list for Wireshark
Subject: SV: [Wireshark-dev] nmake U1077 errors

Hi,

From memorry :-)

The lines were

cd asn1

nmake...

The nmake line should be removed as well...

BR

Anders

 

---

Från: wireshark-dev-bounces@xxxxxxxxxxxxx genom Andrew.Martin@xxxxxxxxxxxxxxxxxxxxxx
Skickat: ti 2006-10-24 11:42
Till: wireshark-dev@xxxxxxxxxxxxx
Ämne: Re: [Wireshark-dev] nmake U1077 errors

I removed that line, but instead I get this error:

 

NMAKE : fatal error U1052: file 'Makefile.nmake' not found
Stop.
NMAKE : fatal error U1077: '"C:\PROGRA~1\Microsoft Visual Studio\VC98\Bin\NMAKE.EXE"' : return code '0x2'
Stop.

---

From: wireshark-dev-bounces@xxxxxxxxxxxxx [mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Anders Broman (AL/EAB)
Sent: 24 October 2006 10:21
To: Developer support list for Wireshark
Subject: SV: [Wireshark-dev] nmake U1077 errors

Hi,

The first problem is due to the asn1 libraries missing from the source you downloaded.

It's fixed in later versions. Either download a source tarball from the buildbot directory

or remove that line from the distclean target in the nmake file.

 

The seciond problem is due to an "error" in Cygwin bash, download an older version.

 

Brg

Anders 

---

Från: wireshark-dev-bounces@xxxxxxxxxxxxx genom Andrew.Martin@xxxxxxxxxxxxxxxxxxxxxx
Skickat: ti 2006-10-24 11:19
Till: wireshark-dev@xxxxxxxxxxxxx
Ämne: [Wireshark-dev] nmake U1077 errors

I'm attepting to write a decoder, well I would if I could get wireshark to compile!

 

I'm on a win2k box and I'm getting the following error when I run nmake -f makefile.nmake distclean:

 

cd asn1
NMAKE : fatal error U1077: 'cd' : return code '0x1'
Stop.

 

I also get the following error when I attempt verify_tools and setup:

 

: command not foundh: line 2:
: command not foundh: line 4:
'ools/win32-setup.sh: line 5: syntax error near unexpected token `{
'ools/win32-setup.sh: line 5: `err_exit () {
NMAKE : fatal error U1077: 'bash' : return code '0x2'
Stop.

 

Any help would be appreciated.

 

 

---

This email and any files attached are intended for the addressee and may contain information of a confidential nature. If you are not the intended recipient, be aware that this email was sent to you in error and you should not disclose, distribute, print, copy or make other use of this email or its attachments. Such actions, in fact, may be unlawful. In compliance with the various Regulations and Acts, General Dynamics UK Limited reserves the right to monitor (and examine for viruses) all emails and email attachments, both inbound and outbound. Email communications and their attachments may not be secure or error- or virus-free and the company does not accept liability or responsibility for such matters or the consequences thereof. Registered Office: 100 New Bridge Street, London EC4V 6JA. Registered in England and Wales No: 1911653.

---

This email and any files attached are intended for the addressee and may contain information of a confidential nature. If you are not the intended recipient, be aware that this email was sent to you in error and you should not disclose, distribute, print, copy or make other use of this email or its attachments. Such actions, in fact, may be unlawful. In compliance with the various Regulations and Acts, General Dynamics UK Limited reserves the right to monitor (and examine for viruses) all emails and email attachments, both inbound and outbound. Email communications and their attachments may not be secure or error- or virus-free and the company does not accept liability or responsibility for such matters or the consequences thereof. Registered Office: 100 New Bridge Street, London EC4V 6JA. Registered in England and Wales No: 1911653.

---

This email and any files attached are intended for the addressee and may contain information of a confidential nature. If you are not the intended recipient, be aware that this email was sent to you in error and you should not disclose, distribute, print, copy or make other use of this email or its attachments. Such actions, in fact, may be unlawful. In compliance with the various Regulations and Acts, General Dynamics UK Limited reserves the right to monitor (and examine for viruses) all emails and email attachments, both inbound and outbound. Email communications and their attachments may not be secure or error- or virus-free and the company does not accept liability or responsibility for such matters or the consequences thereof. Registered Office: 100 New Bridge Street, London EC4V 6JA. Registered in England and Wales No: 1911653.